Our Cicada drone and it’s component parts are all manufactured and assembled in the US/UK. The following parts are available for purchase as individual components. Please note there is an MOQ of 100 per unit. If you wish to buy as individual components please contact info@roark-aerospace.com. If you wish to buy manufacturer kits please head to the bottom of the page.
Frames
5″ Frame
Specifications
Wheelbase: 220mm, Weight: 124.2g, Material: Carbon Fiber, Coating: Graphene PMMA, Propellor Size: 5.1″ Max, VTX Mounting Hole 30.5×30.5, FC Mounting: 30.5×30.5
7″ Frame
Specifications
Wheelbase: 300mm, Weight: 144.6g, Material: Carbon Fiber, Coating: Graphene PMMA, Propellor Size: 7″ Max, VTX Mounting Hole 30.5×30.5, FC Mounting: 30.5×30.5
Motors
XLN
Specification
KN: 1800, Configuration: 12N14P, 22x7x5mm, 33.8g, Cells: 3~6S
XLX
Specification
KN: 2450, Configuration: 12N14P, 22x7x4mm, 32.6g, Cells: 2~4S
Battery
RoarkLipo
Specification
Capacity: 1350mAh, Voltage: 22.2V / 6-Cell / 6S1P, Discharge Rate: 150C Continual / 300C Burst, Charge Rate: 5C Max, Size(1-5mm difference): 38X38X78mm, Approx Weight(±5g) : 215g, Output Connector: XT60, Balance Connector: JST / XH
Boards
Roark 5in1 Board FC + ESC + OSD + VTX + RX
Specification
FC: Weight: 3.6g(5IN1 Version), Mounting Hole Size: 26mm x 26mm, CPU*: STM32G473CEU6 (168MHz), Six-Axis: ICM42688P (SPI connection), Blackbox Memory: 16MB, Sensor: Voltage&Current 5V BEC*: 5V 3A, USB Port: SH1.0 4-Pin, Built-in ESC with 5A continuous, RX: Serial ELRS 2.4G (V3.4.3)
ESC: Input Voltage: 1S FC Firmware Version: Betaflight_4.5.0_BETAFPVG473, ESC Firmware: A_X_5_96KHz_V0.19.hex for BB51 Bluejay hardware, Signal Support: D-shot300, D-shot600
VTX: Output Power: 25/100/200/400/PIT, Frequency: 5.8GHz 48 channels, with Raceband: 5658~5917MHz, Channel SEL: SmartAudio2.0, Modulation Type: FM, Frequency Control: PLL, All Harmonic: Max -50dBm, Frequency Stability: ±100KHz (Typ.), Frequency Precision: ±200KHz (Typ.), Channel Carrier Error: ±1.5dB, Antenna Port: 50 Ω, Operating Temperature: -10℃~+80℃
RX: CRSF
Shielding: Graphene PMMA coating with Graphene Ag modified solder
Propellors
RoarkProp
Specification
- Propeller Diameter: 5.1 inch, Pitch : 3.3, Blades : 3, Material : Poly Carbonate x Graphene PMMA, Weight :3.5g, Hub Diameter :12.5mm, Hub Thickness:6mm, Shaft :5mm, Adaptor Rings : NO
Air Unit
RoarkAir FPV Digital Transmission System
Specification
1080p/100fps H.265 Max Video Transmission Quality, 10km Max Video Transmission Range, 30ms Lowest Video Transmission Latency, 1/1.7-inch CMOS Sensor, 4K/60fps, 155° Super-Wide FOV Video. Includes: camera module, transmission module, antenna module
Controller
RoarkGimbal
Specification
MCU: STM32F429IGT6, Screen: 3.5″ color touch 480*320, Display method: IPS, Gimbal size: standard full size gimbals, Gimbal Sensor: Hall sensor gimbals, Protocol: ELRS 2.4GHz / 915MHz / 868MHz optional, Power Output: maximum l000mW (maximum 30dBm), External Module Bay: standard JR module bay, SD card: on-board built-in, Working voltage: 6-8.4v, Battery: 21700*2, 18650*2 or or any 2S Lipo batteries that fit (battery not included), Size:185*175*79mm, Weight: 481g (battery not induded)
Goggles
RoarkGogg
Specification
LCD Screen: Screen size: 3.0 Inch, Resolution: 480*320, Display Ratio: 16:9, View Angle: 6 o’clock, Brightness: 500cd/m² with high brightness backlight LED
Video delay: Video time-delay less than 20ms, Lens: 4X Fresnel Lens, 92% transparent rate no distort of light, Antenna: 2 X RP-SMA male (5.8G), USB: To charge the battery, AV Jack: External video signals input or internals AV signal output, Power adapter: DC5V/1A (USB interface), Battery: 3.7V/1200mAh,Each full charge delivers around 2.5hr working time, Operating current of 300~330mA at 3.7~4.2V, Built-in battery maximum charge current of 500mA, Dimensions: 13.5cm * 13.2cm * 6.5cm, Weight: 180g(with headband, not including antennas).
Also available in 5.0 inch screen version & standalone monitor.
Buying Options
Manufacturer Kit 1 Includes:
100 ea of 5″ frame, XLX Motor, RoarkLipo Battery, Roark 5in1 Board, Roark Propellors, & Roark Air Unit. Approximate build time is 8 minutes per drone.
Price: $13,000
Manufacturer Kit 2 Includes:
100 ea of 5″ frame, XLN Motor, RoarkLipo Battery, Roark 5in1 Board, Roark Propellors & Roark Air Unit. Approximate build time is 9 minutes per drone.
Price: $28,500
Controller and goggles come pre-assembled and can be acquired here
If you wish to purchase using bank transfer please contact info@roark-aerospace.com